{"title":"3D Printing \u0026 Resins","description":"\u003cp\u003ePrinting resins for DLP\/SLA printers – glow-in-the-dark, thermochromic or clear – and epoxy casting resin.\u003c\/p\u003e","products":[{"product_id":"epoxid-giessharz-set-1-kg-harz-0-5-kg-haerter","title":"Epoxy Casting Resin Set – 1 kg Resin + 0.5 kg Hardener S49","description":"\u003cp\u003eA clear, UV-stabilised epoxy casting resin system consisting of 1 kg epoxy resin 100 and 0.5 kg hardener S49. It cures slowly: air bubbles have time to rise, and layers of up to 3 cm can be poured in one go. This makes it a suitable carrier for our glow pigments and glow granules.\u003c\/p\u003e\n\u003ch3\u003eProperties\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\u003cstrong\u003eContents:\u003c\/strong\u003e 1 kg epoxy resin 100 and 0.5 kg hardener S49 – makes 1.5 kg of casting compound\u003c\/li\u003e\n\u003cli\u003e\u003cstrong\u003eMixing ratio:\u003c\/strong\u003e 100 : 47 by weight (resin : hardener)\u003c\/li\u003e\n\u003cli\u003e\u003cstrong\u003eLayer thickness:\u003c\/strong\u003e up to 3 cm in one pour\u003c\/li\u003e\n\u003cli\u003e\u003cstrong\u003ePot life:\u003c\/strong\u003e approx. 12 h 40 min at 20 °C, approx. 2 h 20 min at 30 °C (1,000 g mix, according to the technical data sheet)\u003c\/li\u003e\n\u003cli\u003e\u003cstrong\u003eCuring:\u003c\/strong\u003e at room temperature; fully chemically cured after approx. 14 days at a minimum of 23 °C; post-curing above 40 °C possible\u003c\/li\u003e\n\u003cli\u003e\u003cstrong\u003eAppearance:\u003c\/strong\u003e highly transparent and UV-stabilised\u003c\/li\u003e\n\u003cli\u003e\u003cstrong\u003eApplications:\u003c\/strong\u003e cast and art objects, jewellery, decoration, filling tree trunks, furniture coatings and sealing\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eHow to use the casting resin\u003c\/h3\u003e\n\u003col\u003e\n\u003cli\u003eWeigh out resin and hardener in a ratio of 100 : 47 by weight – for example 200 g resin and 94 g hardener.\u003c\/li\u003e\n\u003cli\u003eStir thoroughly and slowly, including the sides and bottom. Details are given in the enclosed instructions.\u003c\/li\u003e\n\u003cli\u003eFor glow effects, let the mixed resin thicken slightly so that it becomes a little thicker, then stir in the pigment. As a starting point, approx. 20% pigment relative to the resin; test on a small sample first.\u003c\/li\u003e\n\u003cli\u003ePour and leave to cure at room temperature. Rising air bubbles can be removed with a heat gun.\u003c\/li\u003e\n\u003cli\u003ePour objects thicker than 3 cm in several layers.\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003cp\u003e\u003cstrong\u003eTip:\u003c\/strong\u003e Pigments sink in thin, runny resin. If you want an evenly glowing surface, add the pigment to a separate top layer.\u003c\/p\u003e\n\u003ch3\u003eWhat's included\u003c\/h3\u003e\n\u003cp\u003e1 kg lumentics epoxy resin 100, 0.5 kg lumentics hardener S49 and detailed instructions. The processing instructions and technical data sheet are also available for download.\u003c\/p\u003e\n\u003ch3\u003eGood to know\u003c\/h3\u003e\n\u003cp\u003eResin and hardener carry the following hazard statements. \u003cstrong\u003eResin\u003c\/strong\u003e (signal word “Warning”, pictograms GHS07 exclamation mark and GHS09 environment): H315 Causes skin irritation. H317 May cause an allergic skin reaction. H319 Causes serious eye irritation. H411 Toxic to aquatic life with long lasting effects. EUH205 Contains epoxy constituents. May produce an allergic reaction. \u003cstrong\u003eHardener\u003c\/strong\u003e (signal word “Danger”, pictograms GHS05 corrosion, GHS07 exclamation mark and GHS09 environment): H302 + H312 Harmful if swallowed or in contact with skin. H318 Causes serious eye damage. H411 Toxic to aquatic life with long lasting effects. Wear protective gloves, protective clothing and eye protection and work in a well-ventilated area. In case of eye contact, rinse cautiously with water for several minutes; for the hardener, get medical advice immediately. Dispose of residues and containers in accordance with local regulations. All information is given in the safety data sheets for resin and hardener, which you can download from this page.\u003c\/p\u003e","brand":"lumentics","offers":[{"title":"Default Title","offer_id":60213196292480,"sku":"epoxy-set-1kg-s49","price":39.9,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1027\/8554\/8672\/files\/harz-system-01.png?v=1792939296"},{"product_id":"nachleuchtendes-dlp-sla-3d-druckharz-gruenblau","title":"3D Printing Resin Green-Blue 500 g – Glow in the Dark for DLP\/SLA","description":"\u003cp\u003eGlow-in-the-dark printing resin for resin 3D printers with a UV light source around 405 nm. The glow pigments are already mixed in: printed objects charge with light and have a green-blue afterglow in the dark. The resin prints like standard resins; no special settings are needed. In the dark, green-blue looks slightly cooler than green.\u003c\/p\u003e\n\u003ch3\u003eProperties\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\u003cstrong\u003ePrinters:\u003c\/strong\u003e DLP, SLA, LFS, LCD and LCS with a UV source around 405 nm\u003c\/li\u003e\n\u003cli\u003e\u003cstrong\u003eContents:\u003c\/strong\u003e 500 g in a light-protected, leak-proof bottle\u003c\/li\u003e\n\u003cli\u003e\u003cstrong\u003eGlow colour:\u003c\/strong\u003e green-blue; afterglow duration approx. 4 hours, depending on charging, in complete darkness\u003c\/li\u003e\n\u003cli\u003e\u003cstrong\u003ePrint result:\u003c\/strong\u003e high hardness, low shrinkage, low odour during processing\u003c\/li\u003e\n\u003cli\u003e\u003cstrong\u003eMixable:\u003c\/strong\u003e with other printing resins – the glow intensity then decreases proportionally\u003c\/li\u003e\n\u003cli\u003e\u003cstrong\u003eData sheets:\u003c\/strong\u003e safety data sheet and technical data sheet available as downloads\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eHow to print with the glow resin\u003c\/h3\u003e\n\u003col\u003e\n\u003cli\u003eShake the bottle vigorously for at least 2 minutes before pouring. The pigments are heavier than the resin and settle.\u003c\/li\u003e\n\u003cli\u003eStart with your printer's standard values. Because of the slightly thicker consistency, increase the light-off time by 1–2 seconds if necessary.\u003c\/li\u003e\n\u003cli\u003eKeep printed objects to a maximum height of approx. 10 cm; during longer prints the pigments can sink slightly, and the object glows unevenly.\u003c\/li\u003e\n\u003cli\u003eReturn leftover resin to the bottle after printing so that you can reuse it.\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003cp\u003e\u003cstrong\u003eTip for the Elegoo Mars:\u003c\/strong\u003e the build plate has a release coating from the factory. Sand it lightly with not-too-coarse sandpaper and choose a burn-in exposure of at least 60 seconds – in our experience the print then adheres well.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eNo printer of your own?\u003c\/strong\u003e We also offer a 3D printing service – feel free to contact us.\u003c\/p\u003e\n\u003ch3\u003eWhat's included\u003c\/h3\u003e\n\u003cp\u003e500 g glow-in-the-dark 3D printing resin green-blue in a light-protected, leak-proof bottle.\u003c\/p\u003e\n\u003ch3\u003eGood to know\u003c\/h3\u003e\n\u003cp\u003eLabelling under CLP: signal word Warning. Causes skin irritation (H315) and serious eye irritation (H319), may cause an allergic skin reaction (H317) and may cause respiratory irritation (H335); harmful to aquatic life with long lasting effects (H412). Wear protective gloves and eye protection, and ventilate well. Details in the safety data sheet. Solid areas glow more strongly than thin walls. Afterglow is an aid for effects and orientation, visible in real darkness.\u003c\/p\u003e","brand":"lumentics","offers":[{"title":"Default Title","offer_id":60213261926784,"sku":"3d-printer-resin-bluegreen-500g","price":49.9,"currency_code":"EUR","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1027\/8554\/8672\/files\/hero-mit-drucker-weiss-gruenblau.jpg?v=1792939336"},{"product_id":"nachleuchtendes-dlp-sla-3d-druckharz-gruen","title":"3D Printing Resin Green 500 g – Glow-in-the-Dark Resin for DLP\/SLA","description":"\u003cp\u003eGlow-in-the-dark printing resin for resin 3D printers with a UV light source around 405 nm. The glow pigments are already mixed in: printed objects charge with light and glow green in the dark. The resin prints like standard resins; no special settings are needed. Green is the base shade of glow pigments and glows most brightly.\u003c\/p\u003e\n\u003ch3\u003eProperties\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\u003cstrong\u003ePrinters:\u003c\/strong\u003e DLP, SLA, LFS, LCD and LCS with a UV source around 405 nm\u003c\/li\u003e\n\u003cli\u003e\u003cstrong\u003eContents:\u003c\/strong\u003e 500 g in a light-protected, leak-proof bottle\u003c\/li\u003e\n\u003cli\u003e\u003cstrong\u003eGlow colour:\u003c\/strong\u003e green; afterglow duration approx. 4 hours, depending on charging, in complete darkness\u003c\/li\u003e\n\u003cli\u003e\u003cstrong\u003ePrint result:\u003c\/strong\u003e high hardness, low shrinkage, low odour during processing\u003c\/li\u003e\n\u003cli\u003e\u003cstrong\u003eMixable:\u003c\/strong\u003e with other printing resins – the glow intensity then decreases proportionally\u003c\/li\u003e\n\u003cli\u003e\u003cstrong\u003eData sheets:\u003c\/strong\u003e safety data sheet and technical data sheet available as downloads\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eHow to print with the glow resin\u003c\/h3\u003e\n\u003col\u003e\n\u003cli\u003eShake the bottle vigorously for at least 2 minutes before pouring. The pigments are heavier than the resin and settle.\u003c\/li\u003e\n\u003cli\u003eStart with your printer's standard settings. Because of the slightly thicker consistency, increase the light-off time by 1–2 seconds if necessary.\u003c\/li\u003e\n\u003cli\u003eKeep printed objects to a maximum height of approx. 10 cm; during longer prints the pigments can sink slightly and the object glows unevenly.\u003c\/li\u003e\n\u003cli\u003eAfter printing, pour the leftover resin back into the bottle so that you can reuse it.\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003cp\u003e\u003cstrong\u003eTip for the Elegoo Mars:\u003c\/strong\u003e The build plate has a release coating from the factory. Sand it lightly with sandpaper that is not too coarse and choose a burn-in exposure of at least 60 seconds – in our experience the print then adheres well.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eNo printer of your own?\u003c\/strong\u003e We also offer a 3D printing service – just get in touch.\u003c\/p\u003e\n\u003ch3\u003eWhat's included\u003c\/h3\u003e\n\u003cp\u003e500 g glow-in-the-dark 3D printing resin green in a light-protected, leak-proof bottle.\u003c\/p\u003e\n\u003ch3\u003eGood to know\u003c\/h3\u003e\n\u003cp\u003eCLP labelling: signal word Warning. Causes skin irritation (H315) and serious eye irritation (H319), may cause an allergic skin reaction (H317) and may cause respiratory irritation (H335); harmful to aquatic life with long-lasting effects (H412). Wear protective gloves and eye protection and ensure good ventilation. Details in the safety data sheet. Solid areas glow more strongly than thin walls. Afterglow is a visual effect and an aid to orientation, visible in real darkness.\u003c\/p\u003e","brand":"lumentics","offers":[{"title":"Default Title","offer_id":60213263303040,"sku":"3d-printer-resin-green-500g","price":49.9,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1027\/8554\/8672\/files\/hero-mit-drucker-weiss-gruen.jpg?v=1792939337"},{"product_id":"dlp-sla-3d-druckharz-transparent-klar","title":"3D Printing Resin Clear – Transparent Resin for DLP\/SLA, 500 g or 1 kg","description":"\u003cp\u003eTransparent printing resin for resin 3D printers with a UV light source around 405 nm. It is deliberately clear and colourless so that you can tint it yourself with colour or glow pigments – or print it clear. The resin prints like standard resins; no special settings are needed.\u003c\/p\u003e\n\u003ch3\u003eProperties\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\u003cstrong\u003ePrinters:\u003c\/strong\u003e DLP, SLA, LFS, LCD and LCS with a UV source around 405 nm\u003c\/li\u003e\n\u003cli\u003e\u003cstrong\u003eSizes:\u003c\/strong\u003e 500 g or 1 kg, in a light-protected, leak-proof bottle\u003c\/li\u003e\n\u003cli\u003e\u003cstrong\u003eTintable:\u003c\/strong\u003e developed for use with colour and glow pigments\u003c\/li\u003e\n\u003cli\u003e\u003cstrong\u003ePrint result:\u003c\/strong\u003e high hardness, low shrinkage, good flow, low odour, BPA-free\u003c\/li\u003e\n\u003cli\u003e\u003cstrong\u003eMixable:\u003c\/strong\u003e with other printing resins\u003c\/li\u003e\n\u003cli\u003e\u003cstrong\u003eData sheet:\u003c\/strong\u003e technical data sheet available as a download\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eHow to print with the clear resin\u003c\/h3\u003e\n\u003col\u003e\n\u003cli\u003eStart with your printer's standard settings.\u003c\/li\u003e\n\u003cli\u003eIf you stir in pigments: shake the bottle vigorously for at least 2 minutes before every pour so that the pigments are evenly distributed. As a rule of thumb, use approx. 20% pigment relative to the resin; check the mixture with a small test print first.\u003c\/li\u003e\n\u003cli\u003eWith a thicker consistency, increase the light-off time by 1–2 seconds.\u003c\/li\u003e\n\u003cli\u003eKeep printed objects to a maximum height of approx. 10 cm.\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003cp\u003e\u003cstrong\u003eAdhesion to the build plate:\u003c\/strong\u003e Some build plates have a release coating from the factory. Lightly sanding with fine sandpaper and a burn-in exposure of at least 60 seconds for the first layers have proven effective.\u003c\/p\u003e\n\u003ch3\u003eWhat's included\u003c\/h3\u003e\n\u003cp\u003eClear 3D printing resin in the selected size (500 g or 1 kg) in a light-protected, leak-proof bottle.\u003c\/p\u003e\n\u003ch3\u003eGood to know\u003c\/h3\u003e\n\u003cp\u003eLiquid printing resin is a chemical: wear protective gloves, ventilate well and avoid skin contact. The hazard and safety information is on the bottle; we will send you the safety data sheet on request. The clear resin itself does not glow.\u003c\/p\u003e","brand":"lumentics","offers":[{"title":"500 g","offer_id":60213269135744,"sku":"3d-printer-resin-clear-500g","price":34.9,"currency_code":"EUR","in_stock":true},{"title":"1 kg","offer_id":60213269168512,"sku":"3d-printer-resin-clear-1kg","price":64.9,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1027\/8554\/8672\/files\/druckharz-etikett-mockup_transparent.jpg?v=1792939339"},{"product_id":"dlp-sla-3d-druckharz-thermochrom-blau-weiss","title":"3D Printing Resin Thermochromic Blue\/White 500 g – Heat Colour Change","description":"\u003cp\u003eA printing resin with a colour change: objects made from the thermochromic resin are blue and turn white at 37 °C – for example through touch or warm water. As they cool, the blue returns. The resin is designed for resin 3D printers with a UV light source around 405 nm and prints like standard resins.\u003c\/p\u003e\n\u003ch3\u003eProperties\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\u003cstrong\u003eEffect:\u003c\/strong\u003e colour change from blue to white at 37 °C, reversible\u003c\/li\u003e\n\u003cli\u003e\u003cstrong\u003ePrinters:\u003c\/strong\u003e DLP, SLA, LFS, LCD and LCS with a UV source around 405 nm\u003c\/li\u003e\n\u003cli\u003e\u003cstrong\u003eContents:\u003c\/strong\u003e 500 g in a light-proof, leak-proof bottle\u003c\/li\u003e\n\u003cli\u003e\u003cstrong\u003ePrint result:\u003c\/strong\u003e high hardness, low shrinkage, low odour during processing\u003c\/li\u003e\n\u003cli\u003e\u003cstrong\u003eMixable:\u003c\/strong\u003e with other printing resins\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eHow to print with the thermochromic resin\u003c\/h3\u003e\n\u003cp\u003eNo special settings are needed – start with your printer's standard values for standard resin. If the consistency is thicker, increase the light-off time by 1–2 seconds. Keep printed objects to a maximum height of approx. 10 cm. After printing, pour leftover resin back into the bottle so you can reuse it.\u003c\/p\u003e\n\u003ch3\u003eWhat's included\u003c\/h3\u003e\n\u003cp\u003e500 g thermochromic 3D printing resin Blue\/White in a light-proof, leak-proof bottle.\u003c\/p\u003e\n\u003ch3\u003eGood to know\u003c\/h3\u003e\n\u003cp\u003eThis resin does not glow in the dark – it changes colour with temperature. Liquid printing resin is a chemical: wear protective gloves and safety glasses, ventilate well and avoid skin contact. The hazard and safety information is on the bottle; we will send you the safety data sheet on request.\u003c\/p\u003e","brand":"lumentics","offers":[{"title":"Default Title","offer_id":60213270544768,"sku":"3d-printer-resin-thermo-blue-white-500g","price":59.9,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1027\/8554\/8672\/files\/lumentics-3D-Druckharz-Thermochrom-blau-weiss-01.jpg?v=1792939340"}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1027\/8554\/8672\/collections\/listing-04-gruenblau.jpg?v=1793113741","url":"https:\/\/lumentics.de\/en\/collections\/3d-druck-harze.oembed","provider":"lumentics","version":"1.0","type":"link"}